![]() None of this is to say that you can't add a liquid cooler to the top of the case, but it would probably be a better idea to mount the cooler in the front of the case instead. You'll want to do any fine wiring in this neighborhood before tackling the liquid cooling. Right now, it's in a bit of a gray zone-the top of the case is spacious enough that you can access ports on the top of the motherboard (such as the CPU power connector and the CPU fan headers) and even toss in a top-mounted fan or two, but liquid coolers and their thick sandwiches of radiators and fans will likely get in the way of connecting headers up in this area. I could, however, have done with more clearance at the top of the case. After getting the board mounted, I measured just under 1.5 inches of room between the edge of the standard ATX motherboard that I used and this opening, which made plugging in SATA cables quite easy. A ridge toward the front of the case permits cables to pass from the right side of the case (behind the motherboard tray) to the left, but this is positioned far enough forward that it shouldn't get in the way of putting in the motherboard. Hopefully you won't have to do it much, once your build is done.įitting the motherboard into place is easy enough, as there's little in the way to block the board's installation. While getting it and the glass left panel on and off takes some finesse, it's doable with practice. This is most notable with the solid metal right-side panel of my test sample. The most notable issue I found is that the chassis' side panels are neither easy to remove nor to reattach. The Building Experienceīuilding a system into the 4000D Airflow case is a predictable experience, and more positive than negative. We think Corsair should have sprung for the extra port up here, or made both USBs Type-A. Really, this arrangement is often like having just one USB port, because not many devices have a USB cable with Type-C connectors on both ends. That's it.Īs prevalent as USB devices are today, we can all agree that just two USB ports aren't really enough for most folks. Also present are a headphone/microphone combo jack and the usual reset and power buttons. This panel is rather bare by modern standards, with just one USB 3.0 Type-A port and one USB 3.1 Type-C port. The front I/O panel of the Corsair 4000D Airflow (actually up on top of the case) leaves a bit to be desired. A Look at the Front I/OĪ budget case is going to show its stripes in places, and the loadout of ports is one of them here. Like in most cases, however, the vertical-mounting hardware and the necessary GPU riser cable are not included you'll have to find these yourself. The rear panel has two slots for vertical GPU mounting alongside the seven PCI Express card positions. In most such case designs, the supply gets isolated and has to fend for itself in terms of air through the bottom panel. This should help to keep the power supply relatively cool. Unlike on most rival cases, though, the metal sheet separating these two areas is covered in the same triangular perforations seen on the front of the case. The upper compartment holds the motherboard, whereas the lower compartment is walled off behind a shroud that holds the power supply and has room for storage devices. Like many other modern chassis, the 4000D Airflow is broken up into two main compartments. On the inside of the case, the perforations continue. This shouldn't hamper cooling much, however, due to the abundance of ventilation elsewhere and the front-to-back design. The right panel is a solid sheet of steel, and the left panel is tempered glass, without any cut-throughs for air to flow in or out on either side. The two sides of the chassis aren't quite as friendly in the airflow department. Two 120mm Corsair AirGuide fans are pre-mounted (one front, one back) to push things along. Altogether, this makes for a clear path of low resistance for air to pass straight through the case. The top is also perforated and covered by a large magnetic dust filter, and the back of the case has ventilation holes cut in it from top to bottom. In addition to incorporating that perforated front panel, Corsair also left large gaps on either side of this perforated section that permit additional inward ventilation. The "Airflow" in the name is no idle boast. But its affordability and construction quality make it worth a look if you're shopping for a spiffy-on-a-budget PC case while saving up for the stuff inside. Priced at a low $79.99 with a tempered-glass side panel, it's far from the most feature-packed ATX mid-tower we've seen for under $100. Featuring a front panel covered in triangle perforations, Corsair's 4000D Airflow PC case has a distinctive-looking face and delivers what it promises: ample, well, airflow to keep your PC components cool under pressure.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |